; COBOL II Firmware diagnostic (D442A).
;
; Configuration locations UNVERIFIED:
;
;     Location     Default Value  Contents
;   -------------  -------------  --------------------------------------
;   DB+0   044744  000000         External Switch Register setting
;   DB+1   044745  000110         Internal Switch Register setting
;   DB+2   044746  000000         Instruction number to check (00-14)
;   DB+3   044747  000000         
;   DB+4   044750  000000         
;   DB+5   044751  000000         


; Set up the log(s).

set -n console log=zcob.log


; Configure the CPU for the diagnostic.

set cpu 512K,CIS


; Boot the I/O diagnostics tape.

attach -r ms0 30000-11017_Rev-2640_IO.tape
boot ms0


; Load the tape file containing the diagnostic.
;
; The I/O tape contains these files:
;
;   DIAGNOSTIC             FILE    REV   %FILE
;   -------------------   ------  -----   ----
;   SLEUTH                PD411A  01.05   (01)
;   CART DISC-7905A       PD419A  01.04   (02)
;   MEMORY PATTERN        PD421A  01.00   (03)
;   MULTIPLEXOR CHAN      PD422A  01.02   (04)
;   DISC FILE-2888A       PD423A  01.00   (05)
;   CART DISC-7900A       PD424A  01.00   (06)
;   SYSTEM CLOCK  II/III  PD425A  01.00   (07)
;   SYS CLK/FLI   III-LC  PD426A  00.00   (10)
;   TERMINAL DATA         PD427A  01.01   (11)
;   FIXED HEAD DISC       PD428A  01.00   (12)
;   SELECTOR CHAN         PD429A  01.01   (13)
;   FLT.CORR.MEM  SER-II  PD430A  01.01   (14)
;   FLT.CORR.MEM  SER-III PD430B  00.00   (15)
;   EXTEND INSTRUC SET    PD431A  01.00   (16)
;   HSI DIAG.             PD432A  01.00   (17)
;   MAGNETIC TAPE         PD433A  01.04   (20)
;   SSLC INTERFACE        PD434A  01.03   (21)
;   ASLC INTERFACE        PD434B  01.04   (22)
;   UI DIAG               PD435A  01.01   (23)
;   TERMINAL CONTROL      PD438A  01.00   (24)
;   CALCOMP PLOTTER       PD439A  01.01   (25)
;   COBOLII A F/W DIAG    PD441A  00.00   (26)
;   COBOLII B F/W DIAG    PD442A  00.00   (27)
;   STAND ALONE DISC      SADUTIL 01.00   (30)

deposit SWCH 27


; Set the CLK into real-time mode for the timing tests.

set CLK realtime


; Run the diagnostic.

set console delay=1
set -a console halt=COBOL

echo
echo Press <CR> to start the diagnostic.
echo
go


; Set the Switch Register options:
;
; + bit  0 = select the external switch register
;   bit  1 = stop program for reconfiguration
;   bit  2 = not used
;   bit  3 = not used
;   bit  4 = not used
;   bit  5 = not used
;   bit  6 = not used
;   bit  7 = direct messages to the line printer
;   bit  8 = not used
;   bit  9 = suppress non-error messages
;   bit 10 = suppress error messages
;   bit 11 = not used
; + bit 12 = halt on error
;   bit 13 = not used
;   bit 14 = not used
; + bit 15 = halt at the end of each diagnostic pass

set console nohalt

deposit SWCH 100011


; Run the diagnostic.

echo
echo Reconfiguring the switch register and executing the diagnostic.
echo Expect halt 15 for successful completion.

go


; End the of diagnostic.
;
; Verify HALT 15 for a successful pass.

assert CIR=030375


; Restore the hardware configuration.

set CLK caltime