; Execute GICDIAG tests 1-24.


; Load the GIC diagnostic from the tape.


; Set up the log(s).

set -N console log=GIC124.log
set -N console debug=GIC124-debug.log


; Establish the initial environment.
;
; The CPU clock must be REALTIME to pass GICDIAG section 24 (timeouts).

echo
echo Configuring the simulation environment.

set CPU 512K,REALTIME

set console DEL=177

break delay 30 milliseconds


; Remove all devices from the HP-IB

set DC DISABLED

set GIC  COUNT=2
set GICA CHANNEL=11
set GICB CHANNEL=12

set imba debug=csrw;data
set gica debug
set gicb debug
set cpp  debug=cmd;data;opnd;serv


echo
echo
echo -----------------------------------------
echo General I/O Channel Diagnostic Steps 1-24
echo -----------------------------------------
echo
echo Loading the GIC diagnostic.


; Cold load the DUS-III tape.

attach -e -r MS0 DUS-III.tape
boot MS0


echo
echo Configuring the diagnostic.

deposit SWCH 1


; Load and start the diagnostic.
;
; The diagnostic loads from tape and then waits for a <CR>.

echo
echo Starting the diagnostic.

reply "\r" delay 2 seconds


; Configure the diagnostic
;
; Test 18 is omitted as it tests memory parity errors, which are not simulated.

go until ">" ; reply "SWITCHES\r"
go until ">" ; reply "TEST 1/17,19/24\r"
go until ">" ; reply "GO\r"


; Correct the diag from 021001 (LDI 1) to 000600 (ZERO,NOP)

deposit 00.075515 000600


; Respond to "More than one Memory Controller installed in system?(Y/N)"

go until "(Y/N)" ; reply "N\r"


; Respond to "How many channels of all types are there installed? "

go until "installed?" ; reply "2\r"


; Respond to "Set Thumbwheel of GIC under test to channel 00"
;            "Respond 'GO'"

go until ">" ; set GICA channel=0 ; reply "GO\r"


; Respond to "Set Thumbwheel of GIC under test to channel 02"
;            "Respond 'GO'"

go until ">" ; set GICA channel=2 ; reply "GO\r"


; Respond to "Set 'PROCESSOR' switch on GIC under test to 'CPU' ( in)"
;            "Set 'DEVICE TYPE' switch on GIC under test to 'A' ( in)"
;            "Respond 'GO'"

go until ">" ; set GICA CPU,A ; reply "GO\r"


; Respond to "Set 'PROCESSOR' switch on GIC under test to 'CPP' (out)"
;            "Set 'DEVICE TYPE' switch on GIC under test to 'B' (out)"
;            "Respond 'GO'"

go until ">" ; set GICA CPP,B ; reply "GO\r"


; Respond to "Set 'SYS CTRL' switch on GIC under test to 'OFF' (out)"
;            "Respond 'GO'"

go until ">" ; set GICA NOSYS ; reply "GO\r"


; Respond to "Set 'SYS CTRL' switch on GIC under test to 'ON'  ( in)"
;            "Respond 'GO'"
 
go until ">" ; set GICA SYS ; reply "GO\r"


; Respond to "Set Thumbwheel of GIC under test to channel 03"
;            "Respond 'GO'"

go until ">" ; set GICA channel=3 ; reply "GO\r"


; Respond to "Set Thumbwheel of GIC under test to channel 04"
;            "Respond 'GO'"

go until ">" ; set GICA channel=4 ; reply "GO\r"


; Respond to "Set Thumbwheel of GIC under test to channel 05"
;            "Respond 'GO'"

go until ">" ; set GICA channel=5 ; reply "GO\r"


; Respond to "Set Thumbwheel of GIC under test to channel 06"
;            "Respond 'GO'"

go until ">" ; set GICA channel=6 ; reply "GO\r"


; Respond to "Set Thumbwheel of GIC under test to channel 07"
;            "Respond 'GO'"

go until ">" ; set GICA channel=7 ; reply "GO\r"


; Respond to "Set Thumbwheel of GIC under test to channel 08"
;            "Respond 'GO'"

go until ">" ; set GICA channel=8 ; reply "GO\r"


; Respond to "Set Thumbwheel of GIC under test to channel 09"
;            "Respond 'GO'"

go until ">" ; set GICA channel=9 ; reply "GO\r"


; Respond to "Set Thumbwheel of GIC under test to channel 10"
;            "Respond 'GO'"

go until ">" ; set GICA channel=10 ; reply "GO\r"


; Respond to "Set Thumbwheel of GIC under test to channel 11"
;            "Respond 'GO'"

go until ">" ; set GICA channel=11 ; reply "GO\r"


;;; SKIP because second channel is at 12
;;;
; Respond to "Set Thumbwheel of GIC under test to channel 12"
;            "Respond 'GO'"
;
;go until ">" ; set GICA channel=12 ; reply "GO\r"


; Respond to "Set Thumbwheel of GIC under test to channel 13"
;            "Respond 'GO'"

go until ">" ; set GICA channel=13 ; reply "GO\r"


; Respond to "Set Thumbwheel of GIC under test to channel 14"
;            "Respond 'GO'"

go until ">" ; set GICA channel=14 ; reply "GO\r"


; Respond to "Set 'MODE' switch on GIC under test to 'TEST' (out)"
;            "Respond 'GO'"

go until ">" ; set GICA TEST; reply "GO\r"


; Respond to "Set 'PROCESSOR' switch on GIC under test to 'CPU' ( in)"
;            "Respond 'GO'"

go until ">" ; set GICA CPU; reply "GO\r"


; Respond to "Set 'MODE' switch on GIC under test to 'OPER' ( in)"
;            "Respond 'GO'"

go until ">" ; set GICA OPER; reply "GO\r"


; Complete the diagnostic.

go until ">"

exit