; System Clock/Fault Logging Interface diagnostic (D426A).
;   Parameter 1 = path to diagnostic tape.
;
; Configuration locations:
;
;     Location     Default Value  Contents
;   -------------  -------------  ---------------------------------------------------
;   DB+0   016420  000000         Switch Register setting
;   DB+1   016421  074000         Section Select Register setting
;   DB+2   016422  000000         Version and update level
;   DB+3   016423  000003      3  System clock DRT number
;   DB+4   016424  023417   9999  Maximum error print count


echo
echo
echo --------------------------------------------
echo D426A - System Clock/Fault Logging Interface
echo --------------------------------------------
echo
echo Loading the stand-alone loader.


; Cold load the I/O diagnostics tape.

attach -r MS0 %130000-11017_Rev-2640_IO.tape
boot MS0


; Load the tape file containing the diagnostic.
;
; The I/O tape contains these files:
;
;   DIAGNOSTIC             FILE    REV   %FILE
;   -------------------   ------  -----   ----
;   SLEUTH                PD411A  01.05   (01)
;   CART DISC-7905A       PD419A  01.04   (02)
;   MEMORY PATTERN        PD421A  01.00   (03)
;   MULTIPLEXOR CHAN      PD422A  01.02   (04)
;   DISC FILE-2888A       PD423A  01.00   (05)
;   CART DISC-7900A       PD424A  01.00   (06)
;   SYSTEM CLOCK  II/III  PD425A  01.00   (07)
;   SYS CLK/FLI   III-LC  PD426A  00.00   (10)
;   TERMINAL DATA         PD427A  01.01   (11)
;   FIXED HEAD DISC       PD428A  01.00   (12)
;   SELECTOR CHAN         PD429A  01.01   (13)
;   FLT.CORR.MEM  SER-II  PD430A  01.01   (14)
;   FLT.CORR.MEM  SER-III PD430B  00.00   (15)
;   EXTEND INSTRUC SET    PD431A  01.00   (16)
;   HSI DIAG.             PD432A  01.00   (17)
;   MAGNETIC TAPE         PD433A  01.04   (20)
;   SSLC INTERFACE        PD434A  01.03   (21)
;   ASLC INTERFACE        PD434B  01.04   (22)
;   UI DIAG               PD435A  01.01   (23)
;   TERMINAL CONTROL      PD438A  01.00   (24)
;   CALCOMP PLOTTER       PD439A  01.01   (25)
;   COBOLII A F/W DIAG    PD441A  00.00   (26)
;   COBOLII B F/W DIAG    PD442A  00.00   (27)
;   STAND ALONE DISC      SADUTIL 01.00   (30)

deposit SWCH 10


; Set the CLK into diagnostic mode.

set CLK REALTIME


; Load and start the diagnostic.
;
; The diagnostic loads from tape and then waits for a <CR>.

echo
echo Loading the diagnostic.
echo Expect halt 0 if successful.

reply "\r" delay 2 seconds
go


; Verify HALT 0 and respond to Q02 SELECT SWREG OPTIONS.

assert CIR=030360


; Set the Switch Register options:
;
; + bit  0 = select the external switch register
; + bit  1 = modify the Section Select Register
;   bit  2 = not used
;   bit  3 = not used
;   bit  4 = not used
;   bit  5 = loop on the current section
;   bit  6 = not used
;   bit  7 = output to the line printer (if configured)
;   bit  8 = not used
;   bit  9 = suppress non-error messages
;   bit 10 = suppress error messages
;   bit 11 = loop on the last step
;   bit 12 = halt on error
;   bit 13 = halt at the end of each step
;   bit 14 = halt at the end of each section
;   bit 15 = halt at the end of each diagnostic pass

deposit SWCH 140000

echo
echo Configuring the switch register.
echo Expect halt 1 if successful.
echo
go


; Verify HALT 1 and respond to Q03 SELECT SECTION SWREG. OPTIONS.

assert CIR=030361


; Set the Section Select options:
;
;   bit  0 = reconfigure
; + bit  1 = execute Section 1
; + bit  2 = execute Section 2
; + bit  3 = execute Section 3
; + bit  4 = execute Section 4
;   bit  5 = not used
;   bit  6 = not used
;   bit  7 = not used
;   bit  8 = not used
;   bit  9 = not used
;   bit 10 = not used
;   bit 11 = not used
;   bit 12 = not used
;   bit 13 = not used
;   bit 14 = not used
;   bit 15 = not used

deposit SWCH 074000

echo
echo Configuring the section select register.
echo Expect halt 2 if successful.
echo
go


; Verify HALT 2 and respond to Q05 RESTORE SWREG OPTIONS.

assert CIR=030362


; Set the Switch Register options:
;
; + bit  0 = select the external switch register
;   bit  1 = modify the Section Select Register
;   bit  2 = not used
;   bit  3 = not used
;   bit  4 = not used
;   bit  5 = loop on the current section
;   bit  6 = not used
;   bit  7 = output to the line printer (if configured)
;   bit  8 = not used
;   bit  9 = suppress non-error messages
;   bit 10 = suppress error messages
;   bit 11 = loop on the last step
; + bit 12 = halt on error
;   bit 13 = halt at the end of each step
;   bit 14 = halt at the end of each section
; + bit 15 = halt at the end of each diagnostic pass

deposit SWCH 100011


; Run the diagnostic.

echo
echo Reconfiguring the switch register and executing the diagnostic.
echo Expect halt 15 for successful completion.

go


; End the of diagnostic.
;
; Verify HALT 15 for a successful pass.

assert CIR=030375


; Restore the hardware configuration.

set CLK CALTIME