Logging to file "DIAG-MTLOAD.log"


-------------------------------
Loading Diagnostic Configurator
-------------------------------

Configuring the simulation environment.

Loading the diagnostic configurator from magnetic tape.
Expect halt 102077 if successful.

Programmed halt, T: 102077 (HLT 77), P: 77756 (ALF,ALF)

Verifying DSN 000200.

Configuring the diagnostic configurator for magnetic tape loading.
Expect halt 102077 if successful.

Programmed halt, T: 102077 (HLT 77), P: 77237 (JMP 100)


-------------------------------------
DSN 103024 - 12821 ICD Disc Interface
-------------------------------------

Loading the diagnostic.
Expect halt 102077 if successful.

Programmed halt, T: 102077 (HLT 77), P: 77237 (JMP 100)

Verifying DSN 103024.

Configuring the diagnostic.




                  *** HPIB 12821A DIAGNOSTIC ***  


INSTRUCTIONS:

     1. ENTER ? WHEN YOU NEED MORE INFORMATION.

     2. INDICATE OCTAL VALUES BY A FINAL B (E.G. 13B).

     3. SET SR BIT 15 ON TO LOOP ON DIAGNOSTIC,       
        TOGGLE ON,OFF TO BREAK OUT OF A SINGLE TEST   
        LOOP (CONVERSATIONAL-MODE).                   

     4. SET SR BIT 14 TO SUPPRESS PRESET TEST         

     5. SET SR BIT 13 T0 PRINT ONLY ERROR MESSAGES    
        (EXCEPT CONFIGURATION MESSAGES).              

     6. SET SR BIT 12 TO DELAY 1 SECOND BETWEEN TESTS 

IS THE FIRST CARD IN SELECT CODE 43B? 
IF YES, INPUT CARRIAGE RETURN                           
OTHERWISE, INPUT THE CORRECT SELECT CODE.. [CR entered]


INPUT THE LAST OCTAL DIGIT OF THE BUS                   
ADDRESS (0-7 DERIVED FROM S1-S3) ... 5

IS THE SECOND CARD IN SELECT CODE 44B? 
IF YES, INPUT CARRIAGE RETURN                           
IF NO SECOND CARD, INPUT 77B                            
IF DIAGNOSTIC GUESSED INCORRECTLY AND THERE IS          
A SECOND CARD, ENTER CORRECT SELECT CODE... [CR entered]


INPUT THE LAST OCTAL DIGIT OF THE BUS                   
ADDRESS (0-7 DERIVED FROM S1-S3) ... 7


PROGRAM OPTIONS: 


    CR  - CARRIAGE RETURN- (DEFAULT) EXECUTE DIAG.
          FROM TEST 0.                            

     N  - BEGIN EXECUTION FROM TEST N   

    LN  - LOOP ON TEST N                      
          (TOGGLE SW BIT 15 TO REGAIN CONTROL)    

     E  - EXIT PROGRAM WITH HLT77                 
          (PRESS RUN TO RE-ENTER PROGRAM)         

     F  - FORCE TESTING TO SECOND BOARD           

     G  - GO BACK AND RETEST BOARD ONE            

     R  - GO BACK TO RECONFIGURATION SECTION      


? [CR entered]

Executing the diagnostic.

Expect message "PRESS HALT,PRESET,RUN WITHIN 10 SECONDS !".




 PRESS HALT,PRESET,RUN WITHIN 10 SECONDS !        

[PRESET pressed, RUN pressed]
Expect message "TESTING COMPLETED ON SELECT CODE 43B".
followed by "PRESS HALT,PRESET,RUN WITHIN 10 SECONDS !".



 TESTING COMPLETED ON SELECT CODE 43B



 PRESS HALT,PRESET,RUN WITHIN 10 SECONDS !        

[PRESET pressed, RUN pressed]
Expect message "TESTING COMPLETED ON SELECT CODE 44B".
followed by "(T15)..DI TO HP-IB TO DI TEST PASSES !".

Then expect halt 102077 for successful completion.



 TESTING COMPLETED ON SELECT CODE 44B




(T15)..DI TO HP-IB TO DI TEST PASSES ! 

? E

Programmed halt, T: 102077 (HLT 77), P: 00345 (JMP 1563)
sim> q
Goodbye
Log file closed